A frequency counter has an internal frequency reference it uses to compare against the signal being measured. "Time base" is another term for "frequency reference" (frequency being the reciprocal of time, therefore a time reference is also a frequency reference). The more accurate the time base, the more accurate the frequency counter.

The other 3 factors mentioned are insignificant -- an attenuator changes the amplitude of the signal but not the frequency; and the logic components (including a decade divider) have no cumulative effect on accuracy since they are referenced to the time base.

Last edited by gxti. Register to edit

Tags: arrl chapter 7 arrl module 7b

\begin{align} \frac{\text{Ohms}}{\text{volt}} \times \text{full scale volts} &= \text{full scale impedance} \\ &=\text{input impedance} \end{align} (drichmond60)

Hint: all the "When used as..." answers are incorrect.

Hint: The word "voltmeter" appears in the question and in the correct answer.

Last edited by wileyj2956. Register to edit

Tags: arrl chapter 7 arrl module 7b

The 2-port S (scattering) voltage parameters for a linear electrical network are defined as

S₁₁ = input reflection coefficient
S₁₂ = reverse gain
S₂₁ = forward gain
S₂₂ = output reflection coefficient

Therefore, S₂₁ is the forward gain.

Hint: S_ab is the outgoing wave at Port a when there is an incoming wave at Port B and there is no incoming wave at the other port.

See https://en.wikipedia.org/wiki/Scattering_parameters for a summary of the technical explanation

Mnemonic:
21: Big element followed by a small element is a Yagi with forward gain
12: Small element followed by a big element is a Yagi pointing the other way giving reverse gain.
11: The 1 sees a reflection and 1 looks like I for input.
22: The 2 sees a reflection and 2 does not look like an I.

Poor man's hint: In the United States, you look forward to turning 21 years old.

Another stupid hint: the greater number of 2 in S21 is before (forward) the 1. The reverse is true with reverse gain (pun unintended).

One more stupid hint: Watch out, because there are two very similar questions like this. The way you can remember is this question is shorter, so choose the bigger number. The other question is longer, so choose the smaller number. If that makes sense.

Silly Hint: The shifter on a car goes Park, Reverse, Forward, Overdrive... it's very similar to how the S parameters are structured:

• S11 Input (In park)
• S12 Reverse
• S21 Forward
• S22 Output (Overdrive)

Last edited by cq.n8gmz. Register to edit

Tags: arrl chapter 9 arrl module 9g

The 2-port \(S\) (scattering) voltage parameters for a linear electrical network are defined as

\[\begin{align} S_{11} &= \text{input reflection coefficient} \\ S_{12} &= \text{reverse gain} \\ S_{21} &= \text{forward gain} \\ S_{22} &= \text{output reflection coefficient} \\ \end{align}\]

SWR and signal return loss are both calculated by using the input reflection coefficient. Therefore, \(S_{11}\) represents return loss. SWR can be directly calculated from S11 by a simple formula.

See https://en.wikipedia.org/wiki/Scattering_parameters for a summary of the technical explanation

Memory aid: picture the device facing toward the right, with left side numbered as 1 and right as 2. Then 1-2 and 2-1 would be traveling from one end to the other. Only 1-1 both goes in and (back) out on the left side.

Silly memory tip: The straight lines of "11" look like the tips of an electrical plug you "input" into a electrical socket.

Last edited by flyallthethings. Register to edit

Tags: arrl chapter 9 arrl module 9g

\(50\Omega\) ohms is the most common impedance used in RF power systems, and amateur transmitters also use this standard. Therefore it is a useful point to calibrate to. After that, short-circuit and open-circuit are two "boundary cases" that ensure the analyzer behaves correctly at the edges of its range.

Calibrating to \(75\Omega\) or \(90\Omega\) ohms might be somewhat helpful, but after covering the full range with the 3 correct answers there is limited value in any further calibration. The other answers are not simple loads or make no sense at all.

Funny reminder: The movie "short circuit" and the robot Johnny 5. Only 1 answer has "short circuit" and 5 (\(50\Omega\)) in it.

Last edited by kv0a. Register to edit

Tags: arrl chapter 9 arrl module 9g

Where \(P\) is power:

\begin{align} \text{(load absorption)} &= P_\text{forward} - P_\text{reflected} &=100-25=75\:\text{Watts} \end{align}

Last edited by k6bjy. Register to edit

Tags: arrl chapter 9 arrl module 9f

S parameters are a way of measuring the frequency response of devices and can refer to as many ports as are on the device.

For example, an antenna has 1 port, a filter may have 2 ports, a power divider may have 3 or more ports.

The subscripts tell us from which ports the measurements were made and are in the order of "To -> From" or S_<out><in>

So S₁₁ would be a measurement to Port 1, from Port 1. (Perhaps an antenna measurement, or other reflection measurement).

S₂₁ would be a measurement made at port 2 with the signal being delivered from port 1. (Such as measuring a filter to see what frequencies are blocked or passed through).

Silly hint: Submarines go to ports Silly hint: Think "Sports" as in football, basebasell, etc. for S Ports

Last edited by dajaustin. Register to edit

Tags: arrl chapter 9 arrl module 9g

Quick silly attempt at remembering the right answer:

The right answer has "frequency response" in it. So, Every Question (Q) deserves a response

(you're welcome)

Q stands for quality. The frequency response is a measurement of quality.

Definition Of \(Q\) Factor: In the context of resonators, \(Q\) is defined in terms of the ratio of the energy stored in the resonator to the energy supplied by a generator, per cycle, to keep signal amplitude constant, at a frequency \(f_r\) (the resonant frequency), where the stored energy is constant with time:

\[\begin{align} Q &= 2π \times \left( \frac{\text{Energy}_{\text{stored}}}{\text{Energy}_{\text{dissipated per cycle}}} \right) \\ &= 2π\times f_r \times \left( \frac{\text{Energy}_{\text{stored}}}{\text{Power}_{\text{loss}}} \right) \end{align}\]

http://en.wikipedia.org/wiki/Q_factor#Explanation

There are a few ways to define \(Q\). With regard to this question, the bandwidth is the width of the range of frequencies for which the energy is at least half its peak value. The higher the \(Q\), the narrower the bandwidth. That is,

\[\text{bandwidth} = \frac{f_r}{Q}\]

-wileyj2956

Last edited by dogshed. Register to edit

Tags: arrl chapter 4 arrl module 4e

The magnitude of a complex impedance is always higher than its resistive component (see Pythagorean Theorem). This means that a resistive load with a reactive component will always draw less current than the same load with no reactive component.

When an antenna is tuned to resonance its inductive and capacitive reactances add to zero, leaving only the resistive component of the antenna's impedance. As the antenna's reactance is reduced, more current flows into the antenna. Current is maximum when the antenna's reactance is zero.

Increased current means more power is being delivered to the antenna.

Hint: When something increases there is more of it.

Last edited by katzelover. Register to edit

Tags: arrl chapter 9 arrl module 9f

Caution, this one is easy to misread.

Both choices that Modulate the transmitter using two RF signals are distractors because we use audio frequencies (here abbreviated AF) to modulate the carrier in SSB mode.

You can rule out the distractors mentioning logic analyzer, which only handles digital logic signals, and peak reading wattmeter, because it just outputs a watt number - you'd have no way to know if that number represents your signal peak or a intermodulation distortion peak.
Instead you want a spectrum analyser, which shows many frequencies at once, and their current power level, letting you spot intermodulation distortion at nearby frequencies.

That leaves the correct answer Modulate the transmitter with two non-harmonically related audio frequencies and observe the RF output with a spectrum analyzer.

Last edited by nicenjehr. Register to edit

Tags: arrl chapter 7 arrl module 7b

A Vector Network Analyzer is fundamentally a device for measuring incident and reflected power, usually expressed as S Parameters (Scattering Parameters).

While Input Impedance and Output Impedance are not actually S Parameters, these things can be calculated based on a combination of S parameter measurements and calibration data. A VNA will typically calculate these for you based on measurements/calibration and present them to you, therefore they can effectively be used to measure these values. Since Reflection coefficient is an S parameter and the others are normally calculated for you by a VNA, the best answer here is All these choices are correct.

Note that "network" in the name Vector Network Analyzer refers to electrical networks, not computer networks or communication networks. An electrical network is what you see on a schematic diagram.

Last edited by radarchops. Register to edit

Tags: none