Login or Register for FREE!
Subelement E5
ELECTRICAL PRINCIPLES
Section E5A
Resonance and Q: characteristics of resonant circuits: series and parallel resonance; definitions and effects of Q; half-power bandwidth; phase relationships in reactive circuits
What can cause the voltage across reactances in a series RLC circuit to be higher than the voltage applied to the entire circuit?
  • Correct Answer
    Resonance
  • Capacitance
  • Conductance
  • Resistance

From wikipedia:

"In physics, resonance is the tendency of a system to oscillate with greater amplitude at some frequencies than at others. Frequencies at which the response amplitude is a relative maximum are known as the system's resonant frequencies, or resonance frequencies. At these frequencies, even small periodic driving forces can produce large amplitude oscillations, because the system stores vibrational energy.

Resonance occurs when a system is able to store and easily transfer energy between two or more different storage modes (such as kinetic energy and potential energy in the case of a pendulum). However, there are some losses from cycle to cycle, called damping. When damping is small, the resonant frequency is approximately equal to the natural frequency of the system, which is a frequency of unforced vibrations. Some systems have multiple, distinct, resonant frequencies.

Resonance phenomena occur with all types of vibrations or waves: there is mechanical resonance, acoustic resonance, electromagnetic resonance, nuclear magnetic resonance (NMR), electron spin resonance (ESR) and resonance of quantum wave functions. Resonant systems can be used to generate vibrations of a specific frequency (e.g., musical instruments), or pick out specific frequencies from a complex vibration containing many frequencies (e.g., filters)."

Reference: http://en.wikipedia.org/wiki/Resonance

Last edited by ctrstocks. Register to edit

Tags: arrl chapter 4 arrl module 4d

What is resonance in an LC or RLC circuit?
  • The highest frequency that will pass current
  • The lowest frequency that will pass current
  • Correct Answer
    The frequency at which the capacitive reactance equals the inductive reactance
  • The frequency at which the reactive impedance equals the resistive impedance

Resonance: In an electrical circuit, the condition that exists when the inductive reactance and the capacitive reactance are of equal magnitude, causing electrical energy to oscillate between the magnetic field of the inductor and the electric field of the capacitor.

Note 1: Resonance occurs because the collapsing magnetic field of the inductor generates an electric current in its windings that charges the capacitor and the discharging capacitor provides an electric current that builds the magnetic field in the inductor, and the process is repeated.

Note 2: At resonance, the series impedance of the two elements is at a minimum and the parallel impedance is a maximum. Resonance is used for tuning and filtering, because resonance occurs at a particular frequency for given values of inductance and capacitance. Resonance can be detrimental to the operation of communications circuits by causing unwanted sustained and transient oscillations that may cause noise, signal distortion, and damage to circuit elements.

Note 3: At resonance the capacitive reactance and the inductive reactance are of equal magnitude.

Source: http://www.its.bldrdoc.gov/fs-1037/dir-031/_4576.htm

Memory Trick: There are two answers with "equals" in them, but the one with reactance written twice is the correct answer.

Last edited by n9gmr. Register to edit

Tags: arrl chapter 4 arrl module 4d

What is the magnitude of the impedance of a series RLC circuit at resonance?
  • High, as compared to the circuit resistance
  • Approximately equal to capacitive reactance
  • Approximately equal to inductive reactance
  • Correct Answer
    Approximately equal to circuit resistance

In a resonant circuit, the inductive and capacitive reactance are equal and opposite, thus cancelling each other. This leaves the fundamental resistance of the circuit as the only impedance.

If either the inductance or capacitance is greater than the other resulting in non-resonance, the remaining uncancelled impedance adds to the overall impedance of the circuit. The key words here are "at resonance".

Last edited by kb7m. Register to edit

Tags: none

What is the magnitude of the impedance of a parallel RLC circuit at resonance?
  • Correct Answer
    Approximately equal to circuit resistance
  • Approximately equal to inductive reactance
  • Low compared to the circuit resistance
  • High compared to the circuit resistance

When a parallel RLC circuit is at resonance, the reactive impedance is at a maximum. At that point, we have two impedances, call them R1 (R) and R2 (~Z) in parallel. The resistance of two parallel resistors is

\(R_1R_2 \over R_1+R_2\) where \(R_2 \gg R_1\)

this is \(\approx R_1\) (the circuit resistance).


In a resonant circuit, the inductive and capacitive reactance are equal and opposite, thus cancelling each other. This leaves the fundamental resistance of the circuit as the only impedance.

If either the inductance or capacitance is greater than the other resulting in non-resonance, the remaining uncancelled impedance adds to the overall impedance of the circuit. The key words here are "at resonance".

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 4 arrl module 4d

What is the result of increasing the Q of an impedance-matching circuit?
  • Correct Answer
    Matching bandwidth is decreased
  • Matching bandwidth is increased
  • Matching range is increased
  • It has no effect on impedance matching

Here's a good explanation of Q:

https://en.wikipedia.org/wiki/Q_factor

Basically, Q measures how much a circuit or antenna prefers to resonate at a particular frequency. High Q means narrow bandwidth. Resonant circuits are often used as impedance-matching circuits. Because BW = f/Q, increasing the Q of a resonant circuit used for this application has the effect of decreasing the range of frequencies, or bandwidth, over which it can match the impedance between two circuits or between a transmitter and an antenna.

Last edited by kc1tht. Register to edit

Tags: arrl chapter 4 arrl module 4e

What is the magnitude of the circulating current within the components of a parallel LC circuit at resonance?
  • It is at a minimum
  • Correct Answer
    It is at a maximum
  • It equals 1 divided by the quantity 2 times pi, multiplied by the square root of inductance L multiplied by capacitance C
  • It equals 2 multiplied by pi, multiplied by frequency, multiplied by inductance

The important word here is "circulating." While the input current is minimum at resonance, the current circulating between the inductor and the capacitor can be very large, hence the answer to this question is "maximum."

Simple memory trick: "magnitude" starts with 'ma' "maximum" starts with 'ma'

Last edited by km4amj. Register to edit

Tags: arrl chapter 4 arrl module 4d

What is the magnitude of the current at the input of a parallel RLC circuit at resonance?
  • Correct Answer
    Minimum
  • Maximum
  • R/L
  • L/R

The inductor acts as a short circuit at low frequencies while the capacitor acts as a short circuit at high frequencies. Therefore, input current will be high when driven at either very low or very high frequencies.

The definition of resonance in a parallel RLC (resistance (R), inductance (L) and capacitance (C)) circuit is when the impedance of the circuit is at a maximum. If Z is at a maximum, then the input current I must be at a mininum: \(I=\frac{E}{Z}\); as \(Z\) goes to infinity, I goes to zero.

Likewise, the definition for resonance in a series RLC circuit is when \(Z\) is at a minimum, \(I\) is at a maximum.

Rule at resonance:
RLC parallel: min current, max impedance
RLC series: max current, min impedance
Mnemonic: The word "series" has "se" twice, forward at the beginning and backwards at the end, the maximum number of ses. Se=C. C, current, is max.

Memory tip: The question involved two "i" letters -- input and current (I). Choose the answer with two "i" letters -- minimum.

Alternative tip: Min(imum) In(put)

Last edited by dogshed. Register to edit

Tags: arrl chapter 4 arrl module 4d

What is the phase relationship between the current through and the voltage across a series resonant circuit at resonance?
  • The voltage leads the current by 90 degrees
  • The current leads the voltage by 90 degrees
  • Correct Answer
    The voltage and current are in phase
  • The voltage and current are 180 degrees out of phase

When the circuit is in resonance, the inductive reactance and capacitive reactance are equal, so they effectively cancel each other out, with a resulting 0 degree phase angle. This in turn makes the circuit resistive, with the voltage and current in phase.

Hint: There is no mention of inductance nor capacitance; therefore, no leading nor lagging of voltage or current.

Last edited by marvsherman419. Register to edit

Tags: arrl chapter 4 arrl module 4d

How is the Q of an RLC parallel resonant circuit calculated?
  • Reactance of either the inductance or capacitance divided by the resistance
  • Reactance of either the inductance or capacitance multiplied by the resistance
  • Correct Answer
    Resistance divided by the reactance of either the inductance or capacitance
  • Reactance of the inductance multiplied by the reactance of the capacitance

Fundamentally, regardless of circuit configuration, \(Q\) factor is defined as the ratio of reactive power, \(P_X\), over dissipative (resistive) power, \(P_R\):

\[Q = \frac{P_X}{P_R}\]

In a parallel RLC circuit, the input voltage is applied equally across all three branches:

\[V_{In} = V_R = V_L = V_C = V\]

Using the version of the power equation with voltage and impedance terms, and considering that at resonance, reactive impedance of the inductance equals that of the capacitance, solve for reactive and resistive power:

\[P_X = \frac{V_L^2}{X_L} = \frac{V_C^2}{X_C} = \frac{V^2}{X}\]

\[P_R = \frac{V_R^2}{R} = \frac{V^2}{R}\]

Finally, substituting the power equations into the \(Q\) equation and simplifying:

\[Q = \frac{V^2 \over X}{V^2 \over R} = \frac{1 \over X}{1 \over R} = \frac{R}{X}\]

Therefore, \(Q\) of a parallel RLC circuit is calculated as the ratio of resistance divided by the reactance of either the capacitance or inductance.

Hint: Resistance is the first word in only one of the answers for the "parallel" version of this question.

Hint: Q is a ratio therefore it'll be a division (not multiplication).

Hint: RLC is Resistance divided by L or C (inductance or capacitance).

Hint: The correct answer is the only one that starts with "Resistance."

Last edited by ironcal67. Register to edit

Tags: arrl chapter 4 arrl module 4e

How is the Q of an RLC series resonant circuit calculated?
  • Correct Answer
    Reactance of either the inductance or capacitance divided by the resistance
  • Reactance of either the inductance or capacitance multiplied by the resistance
  • Resistance divided by the reactance of either the inductance or capacitance
  • Reactance of the inductance multiplied by the reactance of the capacitance

Fundamentally, regardless of series or parallel configuration, \(Q\) factor is defined as the ratio of reactive power, \(P_X\), over dissipative (resistive) power, \(P_R\):

\[Q = {P_X \over P_R}\]

In a series network, current is equal through each component and through the entire network:

\[I_{in} = I_R = I_L = I_C = I\]

Substituting the version of the power equation with current and resistance terms into the \(Q\) equation:

\[Q = \frac{I_X^2 X}{I_R^2 R} = {I^2X \over I^2 R} = {X \over R}\]

So the Q factor of a series RLC network in resonance equals the ratio of the reactance of either the inductance or capacitance over resistance.


The \(Q\) of an RLC series circuit is defined as

\(Q = {\sqrt{L \over C} \over R}\), and using a little algebra,

\(Q = \frac{X_L}{R}\) and

\(Q = {X_C \over R}\)

so the answer "Reactance of either the inductance or capacitance divided by the resistance" is correct.

Memory tip: Q is a ratio of resistance and reactance. If circuit is series (note the 2 "s"), the denominator has 2 "s", namely resistance. If the circuit is parallel (note the 2 "a"), the denominator has 2 "a", namely reactance.

Also, only the correct answer ends with "divided by resistance."

Last edited by marvsherman419. Register to edit

Tags: arrl chapter 4 arrl module 4e

What is the half-power bandwidth of a resonant circuit that has a resonant frequency of 7.1 MHz and a Q of 150?
  • 157.8 Hz
  • 315.6 Hz
  • Correct Answer
    47.3 kHz
  • 23.67 kHz

\(Q\) is defined as the ratio of the center or resonant frequency \(f\) to the \(3 \text{ dB}\) (half-power) bandwidth:

\[Q = {f \over \text{BW}}\]

therefore

\[\text{BW} = \frac{f}{Q}\]

and in our case

\begin{align} \text{BW} &= {7.1 \text{ MHz} \over 150}\\ &= 0.04733 \text{ MHz} \\ &=47.333 \text{ kHz} \end{align} Just look at the numbers only from small to larger, the second is the answer, and this is true for other similar question on numbers.

Last edited by davidportia. Register to edit

Tags: arrl chapter 4 arrl module 4e

What is the half-power bandwidth of a resonant circuit that has a resonant frequency of 3.7 MHz and a Q of 118?
  • 436.6 kHz
  • 218.3 kHz
  • Correct Answer
    31.4 kHz
  • 15.7 kHz

Given:

\(f_{\text{resonant}} = 3.7 \text{ MHz}\)

\(Q = 118\)

The half-power bandwidth may be calculated as the quotient of the frequency and the \(Q\):

\[BW_{\text{half-power}} \text{ (in MHz)} = \frac{f \text{ (in MHz)}}{Q}\]

So,

\[BW_{\text{half-power}} = \frac{3.7\text{ MHz}}{118} = 0.0314 \text{ MHz}\]

Converted to kHz:

\[ 0.0314 \text{ MHz} \times \frac{1000 \text{ kHz}}{1 \text{ MHz}} = 31.4 \text{ kHz} \]

Quick Clue: Interestingly enough, either way you divide, the first number is "3". Only one answer starts with a "3".

Last edited by greyone. Register to edit

Tags: arrl chapter 4 arrl module 4e

What is an effect of increasing Q in a series resonant circuit?
  • Fewer components are needed for the same performance
  • Parasitic effects are minimized
  • Correct Answer
    Internal voltages increase
  • Phase shift can become uncontrolled

In a series resonant circuit, VL = VC = QVS, in which VS is the source voltage. Thus, for a series resonant circuit, as the Q increases, the voltages across the inductor and capacitor increase. (As a corollary, in a parallel resonant circuit, IL = IC = QIS, in which IS is the source current.)

KNØJI

Hint: Increasing, increase.

Last edited by noji-instructor. Register to edit

Tags: arrl chapter 4 arrl module 4e

What is the resonant frequency of an RLC circuit if R is 22 ohms, L is 50 microhenries and C is 40 picofarads?
  • 44.72 MHz
  • 22.36 MHz
  • Correct Answer
    3.56 MHz
  • 1.78 MHz

We want to find the resonant frequency \((f_0)\) of a series RLC circuit, given:

\begin{align} R &= 22\ \Omega\\ L &= 50\ \mu\text{H} = 5.0 \times 10^{-5}\text{ H}\\ C &= 40\text{ pF} = 4.0 \times 10^{-11}\text{ F} \end{align}

The driven resonant frequency in a series or parallel resonant circuit is \[\omega_0 = \frac{1}{\sqrt{L C}}\]

The angular frequency is \[\omega_0 = 2\pi{f_0}\]

If we combine these two equations, we get \[2\pi{f_0} = \frac{1}{\sqrt{LC}}\]

Rearranging terms: \[f_0 = \frac{1}{2 \pi \sqrt{LC}}\]

Plugging in our values: \[f_0 = \frac{1}{2 \pi \sqrt{\left(5.0 \times 10^{-5}\text{ H}\right) \left(4.0 \times 10^{-11}\text{ F}\right)}}\]

If we plug this into a calculator: \begin{align} &= 3558815\text{ Hz}\\ &= 3.56\text{ MHz} \end{align}


If you forget your calculator on the test, this is going to be take a little work, but it is doable. Let's simplify:

Multiply fractional coefficients and add exponents: \begin{align} f_0 = \frac{1}{2 \pi \sqrt{20 \times 10^{-16}}} \end{align}

Simplify: \begin{align} f_0 &= \frac{1}{2 \pi \sqrt{(2 \times 2 \times 5) \times \left(10^{-8} \times 10^{-8}\right)}}\\ &= \frac{1}{2 \pi \times 2 \times 10^{-8} \times \sqrt{5}}\\ &= \frac{10^8}{4 \pi \sqrt{5}}\\ \end{align}

Estimating that \(4\pi \approx 12.5\) and \(\sqrt{5} \approx 2.2\), we can substitute those values in: \begin{align} f_0 \approx \frac{10^8}{12.5 \times 2.2} &= \frac{10^8}{27.5}\\ &= \frac{10^7}{2.75} \end{align}

\(\frac{10}{2.75}\) is between \(3\) and \(4\), so call it \(3.5\). That gives us: \begin{align} f_0 &\approx \frac{10^7}{2.75}\\ &\approx 3.5 \times 10^6\text{ Hz} = 3.5\text{ MHz}\\ \end{align}

Of the choices, \(3.56\text{ MHz}\) is the closest.

(Let this be a reminder to not forget your calculator for the test!)

https://en.wikipedia.org/wiki/RLC_circuit#Resonance


Multiply the inductance (\(L=50\)) by the capacitance (\(C=40\)) for a product of \(2000\). Take the square root of that product to find \(44.72\) and store that to memory (or write it down). Now multiply \(\pi\) by \(2\) for a product of \(6.283\). Multiply the stored value \(44.72\) by \(6.283\) for a product of \(280.98\). Now divide \(1\) by \(280.98\) for a value of \(0.0035589\). Multiply this by \(1000\) and round up for 3.56 MHz.


For the memory-limited folks like myself, here's a poor man's hint: given the first digits of the problem, the number 3 is missing. 3.56 is your answer.

Another way to look at it is this is an amateur radio test. Only 3.56 is an authorized ham radio frequency.

Another HINT: This is twice the close contender of 1.78 & and is the correct answer 356 days a year. I know, but, now you will remember for sure.

Last edited by yr7 - extra. Register to edit

Tags: arrl chapter 4 arrl module 4d

Which of the following increases Q for inductors and capacitors?
  • Correct Answer
    Lower losses
  • Lower reactance
  • Lower self-resonant frequency
  • Higher self-resonant frequency

Higher \(Q\) indicates a lower rate of energy loss relative to the stored energy of the resonator; the oscillations die out more slowly. See Wiki

The formula for quality factor Q is: \[Q = \frac{2\pi f L}{R}\] where:

  • \(\pi\) is the constant (3.14159...)
  • \(f\) is the frequency in megahertz (MHz)
  • \(L\) is the inductance in Henrys (H)
  • \(R\) is the resistance in ohms (\(\Omega\))

If we make \(R\) lower, \(Q\) will be larger, because we're dividing by \(R\). When we divide by a smaller number, the quotient is larger.

An example of raising the \(Q\) of an inductor (coil) would be to silver plate copper wire. This would raise the \(Q\), compared to copper wire without the silver plating, because silver has a lower resistance than copper.

Easy to remember: Q is quality. Lower losses = higher quality.

Last edited by hb9gwk. Register to edit

Tags: arrl chapter 4 arrl module 4e

What is the resonant frequency of an RLC circuit if R is 33 ohms, L is 50 microhenries and C is 10 picofarads?
  • 23.5 MHz
  • 23.5 kHz
  • 7.12 kHz
  • Correct Answer
    7.12 MHz

The formula for resonant frequency is:

\[f=\frac{1}{2\pi\sqrt{LC}}\]

Where:

  • f - frequency in hertz (Hz)
  • L - inductance in henrys (H)
  • C - capacitance in farads (F)

Notice that even though R is given in the question, it's irrelevant to the calculation. The resonant frequency is dependent on capacitance and inductance, but not on resistance.

Plugging in the values from the question yields:

\begin{align} f&=\frac{1}{2\pi\sqrt{\left(50\times 10^{-6}\right)\left(10\times 10^{-12}\right)}}\\&=7.12\;\text{MHz} \end{align}


Alternate for formula-weak folks like me: given the first digits in the question, 7 is the next number in the sequence.

Last edited by nightdragon. Register to edit

Tags: arrl chapter 4 arrl module 4d

Go to E4E Go to E5B