If you are utilizing remote control of a US station then the rules simply require that the station operate correctly. There is no requirement to add any sort of indicator. Remember that you are still the control operator, even if the control point is not physically located where the station is (i.e. the station is under remote control).

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 2 arrl module 2a

There are online services called "spotting networks" where people can post which callsigns they have been able to hear / make contact with. In a contest it is nearly always against the rules (and always considered bad form) to "self spot" -- that is, to post your own callsign and frequency to the network.

Don't do it =]

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 2 arrl module 2a

On the HF bands, for example, operating on the “WARC bands” is normally prohibited. Therefore, 30 meters is one band on which amateur radio contesting is generally excluded. (E2C03). The other “WARC bands” are 17 meters and 12 meters. They were named after the World Administrative Radio Conference, which in 1979 created a worldwide allocation of these bands for amateur use. Due to their relatively small bandwidth of 100 kHz or less, there is a sort of gentlemen's agreement that the WARC bands may not be used for general contesting.

Hint: as we learned in the technicians and general exams, 30m has a lot of restrictions. This is one.

Last edited by flyallthethings. Register to edit

Tags: arrl chapter 2 arrl module 2a

The FCC designates some frequency bands for unlicensed use: 900 MHz, 2.4 GHz and 5.8 GHz. You may happen to know that these frequencies are often used by small consumer devices such as cordless phones, analog wireless headphones, bluetooth, WiFi access points, and various proprietary wireless devices.

Amateur radio mesh networks are likely to be built using these frequencies because there are more restrictions on unattended operation and less bandwidth available in the HF amateur bands. There is also more hardware available that already uses the unlicensed bands, such as existing WiFi routers. A mesh network can be built by reprogramming existing WiFi routers with little or no hardware modification, for example.

Therefore the answer is Frequencies shared with various unlicensed data services.

HF frequencies are usually subject to more restrictions and have less bandwidth, so this is not a good answer. Cable TV channels 41-43 are not in the amateur allocations and would be illegal to use for this purpose, and the 60m band (one of the most restricted bands) is not available for unattended use. This is why these answers would not make sense.

Hint: The correct answer has "shared" in it, which is like a network (like sharing information).

Last edited by matthew-radio. Register to edit

Tags: none

QSL cards are sent to confirm radio contact. Knowing that, it makes sense that a QSL Manager is someone who handles the sending and receiving of confirmation cards.

Last edited by kk4uwv. Register to edit

Tags: arrl chapter 2 arrl module 2a

Because the VHF & UHF bands often require line of sight, during a contest most activity will concentrate on pulling in weaker signals at the edge of propagation or experimenting with weaker propagation modes like Sporadic-E and Tropo Ducting.

As a result, most of the activity will be found in the weak-signal portions of the bands, often just a few steps away from the calling frequencies. Additionally, US band plans do not define any portions specifically for contesting.

Last edited by ka0s. Register to edit

Tags: arrl chapter 2 arrl module 2a

The Cabrillo standard file format has revolutionized the world of amateur radio competitions. Log files can now be emailed in for adjudication from a variety of different logging software programs.

Last edited by mbtron20. Register to edit

Tags: arrl chapter 2 arrl module 2a

The QSL bureau system was established to help members reduce the costs and hassles of international postage for QSL cards headed to foreign amateurs by packaging many cards headed to the same destination together in one shipment.

Because mailing a QSL card within the US is fairly cheap and easy, the bureau does not facilitate distribution of these cards.

Last edited by ka0s. Register to edit

Tags: arrl chapter 2 arrl module 2a

Normal Wi-Fi 2.4GHz / 5.8GHz wireless equipment can be used for mesh networking, as the ISM bands used for Wi-Fi overlap with amateur allocations.

Amateurs are permitted to use higher power levels (sometimes this can be done in software, or sometimes it requires an external amplifier) and gain antennas than the secondary ISM allocation.

Hint: you run a "router" to make a "network"

Last edited by jerryfaughn. Register to edit

Tags: arrl chapter 8 arrl module 8d

Amateur stations transmitting in foreign countries or regions may have different operating privileges than the receiving stations. In order for a contact to be made, the DX Station must transmit on his authorized frequencies and receive the frequencies permitted to the responding stations.

Also, separating the transmit and receive frequencies can cause less of a "pile up" of callers for the DX station.

Last edited by chrism. Register to edit

Tags: arrl chapter 2 arrl module 2a

In pileups, there are a multitude of operators all transmitting at once in the hopes that the other station (in this case the DX station) will hear their call sign and answer. It's usually hard to pick out

Knowing this, process of elimination:

Sending full callsign and grid square would be annoying/confusing because grid squares are also comprised of letters and numbers which could be mistaken as a call sign.

Sending only the last two letters is brief, yes, but leaves a lot of room for confusion because there's a chance that there's someone else in the pileup that also has those two letters. Also, the DX station will just have to ask for clarification if they hear you, which is a waste of time in pileups and contests.

Sending the DX's call, "this is", then yours, etc. is way too much repetition. Also, it's pretty clear if you're in the pileup that you're trying to reach the DX station. No need to say their call repeatedly, too.

Last edited by honeynebula. Register to edit

Tags: arrl chapter 2 arrl module 2a

Mesh networks are usually either zero configuration or very little configuration; therefore the nodes (routers or hosts) need to discover each other and establish links between each other, since they have not been configured with this information ahead of time.

Network Discovery typically works by nodes either periodically broadcasting a message such as, "I'm here and my name is X" or "I'm here, my name is X, is anyone else there?" This allows nodes to learn what other nodes exist and how to send them messages. (Network discovery is also the means by which your computer learns of nearby Wi-Fi routers.)

But once nodes know of each other's existence, they need to establish links, which can be thought of like imaginary virtual cables over radio. This typically involves a message exchange between nodes, where capabilities (such as protocols and speeds) are negotiated between nodes, such that the best common capabilities are used and incompatible capabilities are rejected. (When you "join a Wi-Fi network" with your computer, you are establishing a link to one or more access points on that Wi-Fi network.)

The other answers don't even make sense for forming a mesh network. The only reasonable answer here is Discovery and link establishment.

Silly hint: Mesh is like linking

Last edited by matthew-radio. Register to edit

Tags: none