Compliance with MPE, or Maximum Permissible Exposure to RF levels (as defined in FCC Part 1, OET Bulletin 65) for “controlled” environments, are averaged over _______ minutes, while “uncontrolled” RF environments are averaged over ______ minutes.
Choose the only correct statement about an aircraft’s Automatic Direction Finding (ADF) equipment.
An aircraft’s ADF transmission exhibits primarily a line-of-sight range to the ground-based target station and will not follow the curvature of the Earth. (13% chose this)
Only a single omnidirectional sense antenna is required to receive an NDB transmission and process the signal to calculate the aircraft’s bearing to the selected ground station. (9% chose this)
All frequencies in the ADF’s operating range except the commercial standard broadcast stations (550 to 1660 kHz) can be utilized as a navigational Non Directional Beacon (NDB) signal. (9% chose this)
An aircraft’s ADF antennas can receive transmissions that are over the Earth’s horizon (sometimes several hundred miles away) since these signals will follow the curvature of the Earth. (68% chose this)
What is the term used to describe a spread spectrum communications system where the center frequency of a conventional carrier is altered many times per second in accordance with a pseudo-random list of channels?
Frequency hopping. (68% chose this)
Direct sequence. (3% chose this)
Time-domain frequency modulation. (18% chose this)
Frequency compandored spread spectrum. (11% chose this)
What is the frequency range of the marker beacon system used to indicate an aircraft's position during an Instrument Landing System (ILS) approach to an airport's runway?
The outer, middle, and inner marker beacons’ UHF frequencies are unique for each ILS equipped airport to provide unambiguous frequency-protected reception areas in the 329.15 to 335.00 MHz range. (10% chose this)
The outer marker beacon’s carrier frequency is 400 MHz, the middle marker beacon’s carrier frequency is 1300 MHz, and the inner marker beacon’s carrier frequency is 3000 MHz. (9% chose this)
The outer, the middle, and the inner marker beacon’s carrier frequencies are all 75 MHz but the marker beacons are 95% tone-modulated at 400 Hz (outer), 1300 Hz (middle), and 3000 Hz (inner). (71% chose this)
The outer, marker beacon’s carrier frequency is 3000 kHz, the middle marker beacon’s carrier frequency is 1300 kHz, and the inner marker beacon’s carrier frequency is 400 kHz. (10% chose this)
The amplitude modulated variable phase signal and the frequency modulated reference phase signal of a Very-high-frequency Omnidirectional Range (VOR) station used for aircraft navigation are synchronized so that both signals are in phase with each other at ____________ of the VOR station.
A circuit that compares the output of a voltage-controlled oscillator (VCO) to a frequency standard and produces an error voltage that is then used to adjust the capacitance of a varactor diode used to control frequency in that same VCO is called what?
What is the name of the condition that occurs when the signals of two transmitters in close proximity mix together in one or both of their final amplifiers, and unwanted signals at the sum and difference frequencies of the original transmissions are generated?
Choose the only correct statement about the localizer beam system used by aircraft to find the centerline of a runway during an Instrument Landing System (ILS) approach to an airport. The localizer beam system:
Operates within the assigned frequency range of 108.10 to 111.95 GHz. (6% chose this)
Produces two amplitude modulated antenna patterns; one pattern above and one pattern below the normal 2.5 degree approach glide path of the aircraft. (6% chose this)
Frequencies are automatically tuned-in when the proper glide slope frequency is selected on the aircraft’s Navigation and Communication (NAV/COMM) transceiver. (10% chose this)
Produces two amplitude modulated antenna patterns; one pattern with an audio frequency of 90 Hz and one pattern with an audio frequency of 150 Hz, one left of the runway centerline and one right of the runway centerline. (78% chose this)
A power transformer has a single primary winding and three secondary windings producing 5.0 volts, 12.6 volts, and 150 volts. Assuming similar wire sizes, which of the three secondary windings will have the highest measured DC resistance?
The 12.6 volt winding. (5% chose this)
The 150 volt winding. (78% chose this)
The 5.0 volt winding. (10% chose this)
All will have equal resistance values. (7% chose this)